Instructions

How to Install Your Luravai Filtered Showerhead™

Installing your new Luravai Filtered Showerhead™ is quick and easy—no plumber required! Follow these simple steps to enjoy spa-like, filtered water in just minutes.

What's Included in Your Package

1 x Luravai Filtered Showerhead™ (with built-in 18-stage filter)
3 x Replacement Filter Cartridges
1 x Stainless Steel Hose (flexible, anti-kink)
1 x Universal Adjustable Connector/Mount
1 x Roll of Teflon/Plumber's Tape
Installation Instructions

Tools You'll Need

Required:

  • Your hands! (Seriously, that's it)

Optional:

  • Adjustable wrench (only if existing showerhead is extremely tight)
  • Clean cloth or towel

Installation Time: 5 minutes or less

Step-by-Step Installation Guide

Step 1: Turn Off the Water

Before you begin, turn off the water supply to your shower. This prevents any unexpected spray or water waste during installation.

Tip: If there's no shut-off valve in your bathroom, simply avoid turning on the shower during installation.

Step 2: Remove Your Old Showerhead

Unscrew your existing showerhead by turning it counterclockwise (lefty-loosey).

  • Most showerheads can be removed by hand
  • If it's stuck, use an adjustable wrench wrapped in a cloth to protect the finish
  • Be prepared for a few drops of residual water

Step 3: Clean the Shower Arm

Inspect and clean the threaded pipe (shower arm) where your old showerhead was attached.

Remove:

  • Old plumber's tape
  • Mineral deposits or buildupAny debris or rust
  • Use a clean, dry cloth to wipe it down. A clean surface ensures a proper, leak-free seal.

Step 4: Apply Teflon Tape (Included)

Wrap the provided Teflon tape around the threads of the shower arm:

  1. Start at the base of the threads
  2. Wrap clockwise (same direction you'll screw on the connector)
  3. Apply 3-4 layers, overlapping slightly
  4. Press the tape firmly into the threads

This creates a watertight seal and prevents leaks.

Step 5: Attach the Adjustable Connector

Screw the universal connector/mount onto the shower arm:

  • Turn clockwise (righty-tighty)
  • Hand-tighten until snug and secure
  • Do NOT over-tighten—hand-tight is sufficient

The connector should feel firm but should not require excessive force.

Step 6: Connect the Stainless Steel Hose

Attach one end of the flexible hose to the connector you just installed:

  • Screw on by hand, turning clockwise
  • Tighten until secure (no tools needed)
  • Ensure the rubber washer inside the hose connector is properly seated

Step 7: Attach the Luravai Showerhead

Connect the other end of the hose to your Luravai Filtered Showerhead™:

  • Screw on clockwise by hand
  • Tighten until secure
  • Check that the rubber washer is in place for a leak-free connection

Step 8: Turn On the Water & Check for Leaks

Slowly turn your water supply back on (or turn on your shower):

  • Let water flow for 10-15 seconds
  • Inspect all connections for leaks:
    • Shower arm to connector
    • Connector to hose
    • Hose to showerhead

If you notice leaks:

  • Turn off water
  • Hand-tighten the leaking connection
  • Add more Teflon tape if needed
  • Test again

Step 9: Adjust Your Showerhead

Position your Luravai showerhead to your preferred angle using the adjustable mount. The flexible hose allows for easy maneuvering.

Step 10: Enjoy Your First Filtered Shower!

Turn on your shower and select your preferred spray mode:

Rainfall Mode – Gentle, spa-like cascade
Mixed Mode – Balanced pressure
Mist Mode – Soothing, steam-like spray
Jet Mode – Powerful, invigorating stream

Experience the difference of clean, filtered water instantly!

Troubleshooting Common Issues

Problem: Water Leaking at Connections

Solution:

  1. Turn off water
  2. Hand-tighten all connections
  3. Check that rubber washers are properly seated
  4. Reapply Teflon tape to shower arm threads if needed
  5. Ensure you're not cross-threading (threads should align smoothly)

Problem: Low Water Pressure

Possible Causes & Solutions:

  1. Filter needs flushing: Run water for 30 seconds to clear any air pockets from the new filter
  2. Hose kinked or twisted: Straighten the hose to allow proper water flow
  3. Flow restrictor (if present): Some homes have flow restrictors—ensure the showerhead is compatible with your system
  4. Clogged shower arm: Clean out the shower arm pipe before installation
  5. Home water pressure: Luravai works best with standard home water pressure (20-80 PSI)
  6. Problem: Showerhead Won't Stay in Position

Solution:

  • Tighten the connector/mount on the shower arm
  • Adjust the angle of the mount
  • Ensure the mount is properly threaded onto the shower arm

Filter Replacement

Your Luravai comes with 3 extra filter cartridges. Replace your filter every 4-6 months (or sooner if you have very hard water).

How to Replace:

  1. Unscrew the showerhead face (counterclockwise)
  2. Remove the old filter cartridge
  3. Insert the new filter cartridge
  4. Screw the showerhead face back on (clockwise)
  5. Run water for 30 seconds to activate the new filter
  6. Filter Lifespan Indicators:
  • Reduced water pressure
  • 4-6 months of use
  • Noticeable change in water quality

Safety & Care Tips

  1. Do NOT over-tighten connections – This can crack plastic threads or damage seals. Hand-tight is sufficient.
  2. Turn off water before installation – Prevents accidents and water waste
  3. Use Teflon tape correctly – Wrap clockwise to prevent tape from unwinding during installation
  4. Check for leaks regularly – Inspect connections monthly to catch potential issues early
  5. Clean your showerhead monthly – Wipe down with a soft cloth; soak in white vinegar if mineral buildup occurs
  6. Store extra filters in a cool, dry place – Keep filters sealed until ready to use

Frequently Asked Questions

Q: Will this fit my shower?
A: Yes! Luravai has a universal connector that fits all standard shower pipes (½-inch NPT threading), which covers 99% of showers in North America and Europe.

Q: Do I need a plumber?
A: No! Installation is tool-free and takes just 5 minutes.

Q: Can I install this on a fixed/wall-mounted showerhead?
A: Yes, you can replace any fixed showerhead with the Luravai handheld system.

Q: What if it leaks after installation?
A: Simply hand-tighten the connection that's leaking. If it persists, reapply Teflon tape to the shower arm threads.

Q: How often should I change the filter?
A: Every 4-6 months for optimal performance, depending on your water quality and usage.

Still Need Help?

Our customer support team is here to assist you!

Email: contact@luravai.com
Phone: +1 (406) 312-9087
Customer Support Hours: Monday – Friday, 9:00 AM – 5:00 PM (MST)

We respond to all inquiries within 24 business hours.